Dumpster Size Calculator (Debris Yards and Tons)
Direct answer: add up the debris volume in cubic yards, then pick the smallest common dumpster (10, 15, 20, 30 or 40 yd) that holds it. Weight = volume × a cited pounds per cubic yard. For a roof, weight = squares × layers × 250 lb per square (ARMA single-layer tear-off, 2.5 lb/sq ft), and volume = weight ÷ 731 lb/yd³ (EPA composition roofing). Example: 20 squares, 1 layer = 5,000 lb (2.5 tons) ÷ 731 ≈ 6.84 yd³, so a 10-yard dumpster. Estimate only. Check weight limits and prohibited items with your hauler.
What to measure
Worked example: Roof: 20 squares × 1 layer × 250 lb = 5,000 lb (2.5 tons); 5,000 ÷ 731 ≈ 6.84 yd³ → 10-yard. Estimate only.
Debris factors and sources
| Debris | Factor | Volume from weight |
|---|---|---|
| Asphalt shingle tear-off | Tear-off lb per square, per layer (ARMA: 250) | lb ÷ 731 lb/yd³ (EPA composition roofing) |
| Drywall, ½ in | lb per sq ft (GA-235: 2.0) | lb ÷ 467 lb/yd³ (EPA gypsum board) |
| Drywall, ⅝ in | lb per sq ft (GA-235: 2.5) | lb ÷ 467 lb/yd³ (EPA gypsum board) |
| Mixed remodel or demolition debris | lb per yd³ (EPA C&D composite: 417) | you enter loose yd³ |
| Lumber or deck boards (incl. treated) | lb per yd³ (EPA lumber: 169) | you enter loose yd³ |
| Carpet | lb per yd³ (EPA carpet: 147) | you enter loose yd³ |
| Carpet padding | lb per yd³ (EPA padding: 62) | you enter loose yd³ |
| Household cleanout (mixed, uncompacted) | lb per yd³ (EPA mixed MSW uncompacted: 250–300) | you enter loose yd³ |
| Concrete rubble | lb per yd³ (EPA concrete: 860) | you enter loose yd³ |
| Dirt and sand | lb per yd³ (EPA dirt and sand: 929) | you enter loose yd³ |
| Refrigerator | lb each (EPA: 250) | lb ÷ 145 lb/yd³ (EPA major appliances) |
| Stove / range | lb each (EPA: 150) | lb ÷ 145 lb/yd³ (EPA major appliances) |
| Dishwasher | lb each (EPA: 125) | lb ÷ 145 lb/yd³ (EPA major appliances) |
| Clothes washer | lb each (EPA: 150) | lb ÷ 145 lb/yd³ (EPA major appliances) |
| Clothes dryer | lb each (EPA: 125) | lb ÷ 145 lb/yd³ (EPA major appliances) |
How it works
Each row adds volume (yd³) and weight (lb). Roof: lb = squares × layers × lb per square; yd³ = lb ÷ 731. Drywall: lb = sq ft × lb per sq ft (Gypsum Association GA-235: 2.0 for ½ in, 2.5 for ⅝ in); yd³ = lb ÷ 467 (EPA gypsum board). Appliances: lb = count × EPA unit weight; yd³ = lb ÷ 145 (EPA major appliances). Loose materials: you enter loose yd³; lb = yd³ × EPA lb/yd³. Tons = lb ÷ 2,000. The suggested size is the smallest of 10, 15, 20, 30 or 40 yd at or above the total; above 40 yd³ it shows how many 40-yard boxes.
EPA's factors are for material as it is collected, not packed. EPA's own spread for mixed household waste (250–300 lb/yd³ uncompacted vs 400–700 compacted) shows how much loading affects volume. Tossed debris with air gaps takes more room than the same weight stacked tightly.
More worked examples
- Roof: 30 squares × 2 layers × 250 = 15,000 lb (7.5 tons) ÷ 731 ≈ 20.52 yd³ → 30-yard.
- Kitchen (example amounts): 200 sq ft ½ in drywall = 400 lb (0.86 yd³) + 6 yd³ mixed debris × 417 = 2,502 lb + fridge 250 + range 150 + dishwasher 125 = 525 lb (3.62 yd³) → 10.48 yd³, 3,427 lb (1.71 tons) → 15-yard.
- Bathroom: 4 yd³ mixed debris (1,668 lb) + 150 sq ft drywall (300 lb, 0.64 yd³) → 4.64 yd³, 1,968 lb → 10-yard.
- Drywall demo: 1,000 sq ft of ½ in = 2,000 lb ÷ 467 ≈ 4.28 yd³ → 10-yard.
- Flooring: 8 yd³ carpet × 147 = 1,176 lb + 4 yd³ pad × 62 = 248 lb → 12 yd³, 1,424 lb → 15-yard.
- Deck removal: 12 yd³ of lumber × 169 = 2,028 lb (1.01 tons) → 15-yard.
- Household cleanout: 25 yd³ × 300 = 7,500 lb (3.75 tons; 6,250 lb at 250) → 30-yard.
How to measure
- Roof: get squares from the roofing calculator (roof area ÷ 100) and count the layers at a cut edge or vent.
- Drywall: wall perimeter × height, plus ceilings, in sq ft (the drywall calculator does this).
- Loose piles: length × width × average height in feet ÷ 27 = yd³. Use the pile helper above.
- Appliances: count them. EPA unit weights are per unit.
- Write down anything heavy (concrete, dirt, tile) separately. Weight limits often matter more than volume.
Common mistakes
- Sizing by volume only and ignoring weight with roofing, concrete or dirt.
- Forgetting extra layers of shingles. Two layers doubles the tear-off weight.
- Measuring a packed pile and then loading loosely. Loose debris takes more room.
- Assuming every hauler accepts every item. Check prohibited items with your hauler.
- Using square feet of floor instead of debris volume for cleanouts.
Assumptions
- Roof tear-off default 250 lb per square per layer from ARMA's Asphalt Shingle Recycling bulletin (2.5 lb/sq ft, single-layer replacement). CT DEEP cites 175–233 lb per square; heavier laminated shingles and wet debris weigh more. Edit the factor.
- Volume factors are from the U.S. EPA Volume-to-Weight Conversion Factors (April 2016), most from a 2006 California C&D study. Actual debris varies with moisture, mix and how tightly it is loaded.
- Household cleanout uses 300 lb/yd³, the upper end of EPA's 250–300 lb/yd³ for uncompacted mixed waste, so the weight estimate is not low. Edit it to 250 for the low end.
- Drywall weights are Gypsum Association GA-235 dead-load values, which may be higher than lightweight boards.
- Project examples are example amounts only. Replace them with your measured squares, areas, pile volumes and counts.
- Dumpster sizes 10/15/20/30/40 yd are common roll-off sizes. Not every hauler offers each. No hauler weight allowances are assumed.
- Estimate only. Check weight limits and prohibited items with your hauler.
Frequently asked questions
What size dumpster do I need for a roof?
Weight = squares × layers × 250 lb (ARMA); volume = weight ÷ 731 lb/yd³ (EPA). 20 squares, 1 layer ≈ 5,000 lb and 6.84 yd³, so a 10-yard. 30 squares, 2 layers ≈ 15,000 lb and 20.5 yd³, so a 30-yard. Check weight limits with your hauler.
How much does a roof tear-off weigh?
ARMA says single-layer tear-off weighs about 2.5 lb per sq ft, or 250 lb per square. CT DEEP cites 175–233 lb per square. A 20-square roof is about 2.5 tons per layer at 250 lb.
How much does a cubic yard of construction debris weigh?
EPA lists mixed construction and demolition debris at 417 lb/yd³, gypsum board 467, roofing 731, concrete 860 and dirt and sand 929.
What size dumpster for a kitchen remodel?
With example amounts (200 sq ft of ½ in drywall, 6 yd³ of mixed debris, a fridge, range and dishwasher), about 10.5 yd³ and 1.7 tons, so a 15-yard. Your amounts will differ.
What size dumpster for a house cleanout?
Measure or estimate the loose volume. At EPA's 250–300 lb/yd³ for uncompacted mixed household waste, 25 yd³ is about 3.1–3.75 tons and fits a 30-yard.
Why does debris take more space than I measured?
Loose debris has air gaps. EPA's range for household waste is 250–300 lb/yd³ uncompacted vs 400–700 compacted, so the same weight can take roughly twice the volume when loose.
Does concrete or dirt fill a dumpster by weight first?
Often. EPA lists concrete at 860 lb/yd³ and dirt and sand at 929, so 10 yd³ of either is over 4 tons. Check weight limits and prohibited items with your hauler.
Related calculators
- Roofing square calculator (squares and bundles) – for roof squares from your footprint and pitch
- Drywall calculator (sheets) – for wall and ceiling sheet area
- Flooring calculator (boxes) – for floor area
- Fill dirt calculator – for dirt and fill volume
- Deck board calculator – for deck board counts
- Cubic yards and cubic feet calculator – for any pile or box volume
Sources
Formulas and reference values are from these sources. Page content last updated 2026-11-05.
- U.S. EPA: Volume-to-Weight Conversion Factors (April 2016): C&D, roofing, gypsum, appliance, carpet and MSW lb/yd³
- ARMA Technical Bulletin: Asphalt shingle recycling (single-layer tear-off about 2.5 lb per sq ft)
- Connecticut DEEP: Asphalt shingles (175–233 lb per square, citing ARMA)
- Gypsum Association GA-235: Gypsum board typical mechanical and physical properties (weight 2.0 psf at ½ in, 2.5 psf at ⅝ in)
- IKO: How many square feet in a bundle of shingles (a square = 100 sq ft; most shingles 3 bundles per square)
- NIST Guide to the SI (SP 811), Appendix B.9: conversion factors (foot = 0.3048 m, ton, pound)